Clear Timber Varnish

Australia’s own environmentally friendly, low odour, water based varnish providing premium protection for your internal timber surfaces with high UV absorption.

This fast drying, high performance varnish incorporates high UV technology to protect your timber from the harmful effects of UV light exposure. With excellent adhesion and a high block resistance it provides a tough protective coating. Designed with the harsh Australian climate in mind this product provides superior timber protection without the need for chemical clean up. A family friendly varnish that packs a protective punch!

Do not apply if temperature is below 10°C or if rain is expected within 24 hours.

icon_60_ausmadewater based
Ecocel Clear Timber Varnish
Available sizes: 500ml, 1L, & 4L
Bondall Paint & Varnish Stripper is a highly effective non-Methylene Chloride stripper ideal for use by inexperienced DIYers as well as professional users. The non-caustic formulation is quick and easy to use, both indoors and out, and can remove multiple layers at a time.
Suitable for use on wood, metal, glass, plaster and concrete. May not be used on plastics. Also suitable for removing old hardened paint from paint brushes, rollers and tools.
Coverage: 1 Litre is sufficient to strip a surface area of approximately 1 square metre.
Application: Pour a quantity of Bondall Paint & Varnish Stripper into a suitable container. Apply a generous, thick coat at a rate of 1 litre per 1 metre squared, onto the surface to be stripped, with a suitable brush. Leave for approximately 1 hr before applying a second coat. For areas where there are less than 5 layers of paint or varnish, a second coat may not be necessary. Once the stripper has softened the paint, scrape off, leaving surface as clean as possible. Repeat process if necessary. Rub down stripped area using a scrubbing brush or stainless steel pad (DO NOT USE WIRE WOOL). Wash down stripped area with Bondall Waterbased TURPS, or detergent and water. Rinse with clean water and allow to dry.
  • Non flammable
  • Water based
  • No drips, runs or waste
  • Suitable indoor & outdoor use

step1Preparation

Carefully clean and prepare all surfaces, fine sanding and rounding off sharp edges as necessary.

Remove all previous paint, varnish, shellac or lacquer and wipe the surface clean of dust.

step2Application

Stir well for 5 minutes and then apply with an applicator pad. The first application is a sealer coat.

Thinning is not usually necessary but if you prefer, thin with 5% clean water and apply as above. Leave this coat to dry for 1 hour, fill any imperfections and then leave to dry fully for 4 hours before applying further coats.

step3Drying

Leave the sealer coat to dry fully for 4 hours then apply a further 2-3 undiluted coats.

Allow 4 hours drying time between each coat. We recommend you give your newly sealed timber a light sanding with 240-grit sandpaper, dusting off thoroughly with a tack rag, before proceeding to apply the undiluted coats.

Features & Benefits

 
  • Single pack
  • Hard durable finish
  • Excellent durability and gloss retention

Ideal For

  • Furniture
  • Timber panelling
  • Architraves
  • Most dressed timber
  • Plywood
  • Doors and windows
  • MDF

Finishes


MonCTF_Bare

Bare Timber

MonCTF_Satin

Satin


MonCTF_Gloss

Gloss

Areas Of Use

GCTV_1
GCTV_2
GCTV_3

Technical

Toughness of Finish

High Toughness of Finish

UV Protection Level

High UV protection Level
Apply: Brush, Pad or Spray
Coverage: 1L = 16m2
Apply: Min 3 Coats
Drying Time: Touch Dry 1 Hr. Re-coat 4 Hrs.

Tips

  • Not recommended for rough sawn surfaces
  • Stir often throughout application to ensure an even coat.
  • This product is normally touch dry in 1 hour but drying may take longer if the weather is cold or humid.

Clean - Up

Cleaning is as easy as 1-2-3!

Safety

Videos

video-blank

Video Title

video-blank

Video Title